Netgear Extender Won’t Connect to Router? Fix It Quickly!
Home / Netgear Extender Won’t Connect to Router? Fix It Quickly!

Netgear Extender Won’t Connect to Router? Fix It Quickly!

Netgear Extender Won’t Connect to Router? Fix It Quickly!

The Netgear extender won’t connect to router issue is known to ruin the online experience of more than 80% of Netgear users. If you are also facing connectivity problems with your WiFi devices, then you’ve crossed paths with the perfect post. Here, we’ve discussed everything related to the problem. It means you’ll learn about the scenarios when the issue is most likely to occur and also the solutions to fix it.

However, you can always start the troubleshooting process by power cycling your WiFi range extender. As soon as you are done restarting the device, re-launch the Netgear extender setup wizard on your computer and see if your router’s network is available now or not. If not, then the time to enter Stage 1 of the troubleshooting procedure has come. In other words, you should now learn why the connectivity issue between your WiFi devices occurred in the first place.

Why Your Netgear Extender Won’t Connect to Router?

If your extender is unable to connect to the router during or after the installation process, the following might be the cases:

Case 1: No Connection Under Any Circumstances

This is the very first scenario in which you assume that your range extender is unable to connect to the router by no means. Chances are that your WiFi devices are not present within range.

Case 2: Extender Connected But No Internet

The second case when the user assumes that the Netgear extender won’t connect to router is that the devices actually connect, but what the extender lacks is an internet connection. One can blame faulty hardwired connections between devices for that.

Case 3: Extender Can’t Scan the Router’s WiFi

Thirdly, your wireless range extender won’t connect to router if the latter’s network isn’t being scanned by the former. It may happen if both devices are either placed too far or too close. Any fault in the product you own can also cause the issue.

Case 4: Patchy Internet Connection from Router

Lastly, the problem in the discussion is likely to show up if there’s a patchy internet connection from the router’s end. You can again put all blame on the Ethernet cable connecting both devices. Perhaps, it is damaged or the connection is loose.

Keeping all 4 cases in mind, a few solutions might have arisen in your mind. If they haven’t, then let’s mention them to you. You can call it Stage 2 of the troubleshooting process. However, after that, we will also make you familiar with a few other techniques that can assist you to address the connectivity issue in the best possible way.

Netgear Extender Won’t Connect to Router: Simple Fixes

  • Keeping Case 1 and Case 3 in mind, you need to ensure that your Netgear wireless range extender is present within the range of the router. If possible, place them in the same room. But, they should not be seated right next to each other.
  • If you have studied Cases 2 and 4, then it is clear that the extender is unable to connect to the internet because your host router itself lacks the internet connection. In that case, you should consider checking the cable connections [Power and Ethernet] related to the router.

So, this was what to do if your Netgear extender won’t connect to router. Now, let us hope that you’ve achieved success with the troubleshooting process just by implementing the simple hacks. In case you’re still finding yourself unlucky, don’t wait to enter Stage 3 where advanced techniques have been mentioned to get the problem troubleshot.

Still Netgear Extender Won’t Connect to Router?

FYI, the advanced tips mentioned below apply equally no matter if you have done AC1750 extender setup or have installed another amazing extender model brought in by Netgear.

Fix 1: Re-run the Netgear Genie Wizard

Chances are that you were following incorrect instructions while trying to establish a connection between the extender and router. Therefore, right from powering up your wireless range extender and accessing the BASIC Home screen, re-do everything and see if you are able to fix the problem. During the entire process, your WiFi devices must be receiving a fluctuation-free power supply.

Fix 2: Perform Factory Reset

In the previous solution, we asked you to re-run the setup process. But, it looks like you still failed. Well, there’s a probability that some serious mistake has been committed by you during the first attempt to do Netgear extender setup. Therefore, you need to correct it. And for that, performing factory reset of the device is what we recommend.

In the Final Analysis

From everything we’ve discussed here, it is clear that a faulty cable connection, an improper distance, or incorrect execution of the setup process is the reason behind the issue. Now, we are expecting that you’ve successfully made the required amendments and are having a wonderful internet experience after fixing the Netgear extender won’t connect to router issue.

    Diclaimer: We, mywifiexxt.us are independent self-sustaining online experts to help you setup WiFi Range Extenders. Any usage of images, logos, product images, and trademarks are just for informational purposes. We are third-party independent online support service provider whose services are provided only on demand/request by users or customers.